Home
when radio is on air you can tune in by clicking on the Peppies-Jukebox link on the top of the page (members only) and by leaving it open you can browse the site content and join in with stuff all at the same time or if you join us you can join us in the irc channel to see whats being played, make requests and join in with us there too. 
Contents
* 1 Why you want to JTAG your XBOX 360?
* 2 Tools needed
* 3 How do I know my XBOX 360 is hackable?
* 4 Which Dashboard-Version does my console have?
* 5 Prepare TIAO 360 USB SPI Interface
* 6 Prepare XBOX 360 for Flashing
* 7 Connect the USB SPI Interface to XBOX 360
* 8 Soldering the SMC-JTAG connection
Buy Game Console Adapters from [You must be registered and logged in to see this link.] or [You must be registered and logged in to see this link.]
Why you want to JTAG your XBOX 360?
If you want to run homebrew... simple enough!
In this tutorial I am going to show you how to modify your XBOX 360 to run Xell Homebrew or xbox rebooter kernel.
Tools needed
[You must be registered and logged in to see this image.]
In order to finish this task, you need to prepare the following tools/components:
1. A ‘hackable’ XBOX 360
2. XBOX 360 USB SPI & JTAG bundle
3. Solder iron, solder and solder paste.
Software needed:
1. Microchip USB package (contains PDFUSSB.exe for flashing PICFLASH.hex over USB)
2. PICFLASH_v3b_plus2
3. NANDPro ( currently Version 2.0 d)
4. Infectus NAND Checker (current Version 1.1)
5. MD5 Comparison Tool (hex editors can do this)
6. 360 Flash Tool ( currently Version 0.91)
7. CD Info (currently Version 1b)
The benefit of using this USB SPI inteface is, it does not require any parallel port (most PCs don't have it nowdays), it only requires USB port. Another advantage is speed. It is 10 times faster than the parallel port tool.
OK, let’s start!
How do I know my XBOX 360 is hackable?
This is relatively easy, check the power connector:
[You must be registered and logged in to see this image.]
Differences between Xenon/Zephyr: Zephyr has HDMI, Xenon does not.
Difference between Falcon/Opus: Falcon has HDMI, Opus does not.
If you have a Jasper box, you should also check which NAND size it has.
Unplug all storage devices (HDD, Memory Unit etc.) and navigate to "System Settings", "Memory". If you don't see a storage device listed there you have a Jasper without an integrated Memory Unit, so you have a 16MB NAND. If a storage device is listed (with a symbol of an Xbox console in front) press the Y-Button and a summary from the storage device will appear.
[You must be registered and logged in to see this image.]
Identification:
Capacity: 214MB = 256MB NAND
Capacity: 451MB = 512MB
Which Dashboard-Version does my console have?
At first you have to find out which dashboard version your Xbox console has. Go to "System Settings", "Console Settings" and choose "System Info". The dashboard should show something like "2.0.7371.0".
[You must be registered and logged in to see this image.]
It is possible to use the hack up to Version 7371, but starting with Dashboard-Version 8xxx it isn't possible anymore.
With Jasper, beginning MFR July 2009, you have to read out the NAND first anyway to know for sure that the Hack will work. (The NAND should be read out anyway, doesn't matter which Mainboard-Revision you have).
Prepare TIAO 360 USB SPI Interface
First, download and install Microchip USB package.
After you have it installed, you should have a menu created something like: MicroChip ->MCHPFSUSB v1.3 in your windows menu bar. Please also remember the install location of this package, as you need to install drivers later. Reboot your machine.
Now, open the TIAO 360 USB SPI interface package, use the jumper to short the BL pins as shown below:
[You must be registered and logged in to see this image.]
hen, connect it to your PC using a mini USB cable (comes with almost all digital camera):
[You must be registered and logged in to see this image.]
You will see the PWR light is on, and you should also hear a beep from you pc indicating a new hardware is found.
Following the following screens to install MiroChip USB Driver:
[You must be registered and logged in to see this image.]
The driver is located in your MicroChip USB package installation, as shown in above picture.
[You must be registered and logged in to see this image.]
After you have specified the location of microchip driver, click Next to install the driver.
Once your driver is installed, unplug the USB cable, and re-plug it in, then run PDFSUSB.exe to load the firmware to PIC:
[You must be registered and logged in to see this image.]
Run the PDFSUSB tool from your start menu. Select the only option in the drop down menu and click load HEX button:
[You must be registered and logged in to see this image.]
Browse to where you unzipped PICFLASH_v3b_plus2 and select file: PICFLASH.hex:
[You must be registered and logged in to see this image.]
Then, click "Program Device" button:
[You must be registered and logged in to see this image.]
If no errors, you have successfully programmed the PIC.
Now, disconnect the 360 USB SPI interface board from your PC by unplug the USB cable, then disable bootloader mode by replacing the jumper to the bottom:
[You must be registered and logged in to see this image.]
Then, plug the interface back to your USB, you will see the LED is on again and Windows found new hardware wizard should come up:
[You must be registered and logged in to see this image.]
Then browse to the location where you unzipped NANDPro2d:
[You must be registered and logged in to see this image.]
Then click next to install the driver.
After the driver is installed, you should have Memory Access installed:
[You must be registered and logged in to see this image.]
Now, you have your TIAO 360 USB SPI interface ready.
Prepare XBOX 360 for Flashing
This step is exactly same for both Parallel port and USB port tool. Please following the instruction below to get it ready:
Read "Preparation" only:
Attention: DO NOT INSTALL DIODES, otherwise it will not work. You need to install diodes AFTER you have flashed your NAND.
How to JTAG XBOX 360
Connect the USB SPI Interface to XBOX 360
This step is easy, make sure the interface board is disconnected from your PC and of course no power to you XBOX 360 as well, using the supplied female to female flexible wire to connect the following:
J1D2 Pin 1 -> J1D2.1 on USB SPI interface board
J1D2 Pin 2 -> J1D2.2
J1D2 Pin 3 -> J1D2.3
J1D2 Pin 4 -> J1D2.4
J1D2 Pin 6 -> GND
J2B1 Pin 5 -> J2B1.5
J2B1 Pin 6 -> J2B1.6
Make sure no short circuits.
[You must be registered and logged in to see this image.]
If everything is ok, plug the USB cable to the SPI interface board, then connect the power adapter to you XBOX 360 but DO NOT turn on it. Just plug the power plug to the wall outlet and power connector to your xbox 360.
So all the cable connections are ready, you can then following the instruction mentioned in [here] (start from page 7, 4.Reading out the NAND to page 13) to read the nand and write the NAND. Make sure to use interface USB, so the command to read NAND is:
nandpro usb: -r16 nandback.bin
Soldering the SMC-JTAG connection
Read "Soldering the SMC-JTAG connection" at:
How to JTAG XBOX 360
* 1 Why you want to JTAG your XBOX 360?
* 2 Tools needed
* 3 How do I know my XBOX 360 is hackable?
* 4 Which Dashboard-Version does my console have?
* 5 Prepare TIAO 360 USB SPI Interface
* 6 Prepare XBOX 360 for Flashing
* 7 Connect the USB SPI Interface to XBOX 360
* 8 Soldering the SMC-JTAG connection
Buy Game Console Adapters from [You must be registered and logged in to see this link.] or [You must be registered and logged in to see this link.]
Why you want to JTAG your XBOX 360?
If you want to run homebrew... simple enough!
In this tutorial I am going to show you how to modify your XBOX 360 to run Xell Homebrew or xbox rebooter kernel.
Tools needed
[You must be registered and logged in to see this image.]
In order to finish this task, you need to prepare the following tools/components:
1. A ‘hackable’ XBOX 360
2. XBOX 360 USB SPI & JTAG bundle
3. Solder iron, solder and solder paste.
Software needed:
1. Microchip USB package (contains PDFUSSB.exe for flashing PICFLASH.hex over USB)
2. PICFLASH_v3b_plus2
3. NANDPro ( currently Version 2.0 d)
4. Infectus NAND Checker (current Version 1.1)
5. MD5 Comparison Tool (hex editors can do this)
6. 360 Flash Tool ( currently Version 0.91)
7. CD Info (currently Version 1b)
The benefit of using this USB SPI inteface is, it does not require any parallel port (most PCs don't have it nowdays), it only requires USB port. Another advantage is speed. It is 10 times faster than the parallel port tool.
OK, let’s start!
How do I know my XBOX 360 is hackable?
This is relatively easy, check the power connector:
[You must be registered and logged in to see this image.]
Differences between Xenon/Zephyr: Zephyr has HDMI, Xenon does not.
Difference between Falcon/Opus: Falcon has HDMI, Opus does not.
If you have a Jasper box, you should also check which NAND size it has.
Unplug all storage devices (HDD, Memory Unit etc.) and navigate to "System Settings", "Memory". If you don't see a storage device listed there you have a Jasper without an integrated Memory Unit, so you have a 16MB NAND. If a storage device is listed (with a symbol of an Xbox console in front) press the Y-Button and a summary from the storage device will appear.
[You must be registered and logged in to see this image.]
Identification:
Capacity: 214MB = 256MB NAND
Capacity: 451MB = 512MB
Which Dashboard-Version does my console have?
At first you have to find out which dashboard version your Xbox console has. Go to "System Settings", "Console Settings" and choose "System Info". The dashboard should show something like "2.0.7371.0".
[You must be registered and logged in to see this image.]
It is possible to use the hack up to Version 7371, but starting with Dashboard-Version 8xxx it isn't possible anymore.
With Jasper, beginning MFR July 2009, you have to read out the NAND first anyway to know for sure that the Hack will work. (The NAND should be read out anyway, doesn't matter which Mainboard-Revision you have).
Prepare TIAO 360 USB SPI Interface
First, download and install Microchip USB package.
After you have it installed, you should have a menu created something like: MicroChip ->MCHPFSUSB v1.3 in your windows menu bar. Please also remember the install location of this package, as you need to install drivers later. Reboot your machine.
Now, open the TIAO 360 USB SPI interface package, use the jumper to short the BL pins as shown below:
[You must be registered and logged in to see this image.]
hen, connect it to your PC using a mini USB cable (comes with almost all digital camera):
[You must be registered and logged in to see this image.]
You will see the PWR light is on, and you should also hear a beep from you pc indicating a new hardware is found.
Following the following screens to install MiroChip USB Driver:
[You must be registered and logged in to see this image.]
The driver is located in your MicroChip USB package installation, as shown in above picture.
[You must be registered and logged in to see this image.]
After you have specified the location of microchip driver, click Next to install the driver.
Once your driver is installed, unplug the USB cable, and re-plug it in, then run PDFSUSB.exe to load the firmware to PIC:
[You must be registered and logged in to see this image.]
Run the PDFSUSB tool from your start menu. Select the only option in the drop down menu and click load HEX button:
[You must be registered and logged in to see this image.]
Browse to where you unzipped PICFLASH_v3b_plus2 and select file: PICFLASH.hex:
[You must be registered and logged in to see this image.]
Then, click "Program Device" button:
[You must be registered and logged in to see this image.]
If no errors, you have successfully programmed the PIC.
Now, disconnect the 360 USB SPI interface board from your PC by unplug the USB cable, then disable bootloader mode by replacing the jumper to the bottom:
[You must be registered and logged in to see this image.]
Then, plug the interface back to your USB, you will see the LED is on again and Windows found new hardware wizard should come up:
[You must be registered and logged in to see this image.]
Then browse to the location where you unzipped NANDPro2d:
[You must be registered and logged in to see this image.]
Then click next to install the driver.
After the driver is installed, you should have Memory Access installed:
[You must be registered and logged in to see this image.]
Now, you have your TIAO 360 USB SPI interface ready.
Prepare XBOX 360 for Flashing
This step is exactly same for both Parallel port and USB port tool. Please following the instruction below to get it ready:
Read "Preparation" only:
Attention: DO NOT INSTALL DIODES, otherwise it will not work. You need to install diodes AFTER you have flashed your NAND.
How to JTAG XBOX 360
Connect the USB SPI Interface to XBOX 360
This step is easy, make sure the interface board is disconnected from your PC and of course no power to you XBOX 360 as well, using the supplied female to female flexible wire to connect the following:
J1D2 Pin 1 -> J1D2.1 on USB SPI interface board
J1D2 Pin 2 -> J1D2.2
J1D2 Pin 3 -> J1D2.3
J1D2 Pin 4 -> J1D2.4
J1D2 Pin 6 -> GND
J2B1 Pin 5 -> J2B1.5
J2B1 Pin 6 -> J2B1.6
Make sure no short circuits.
[You must be registered and logged in to see this image.]
If everything is ok, plug the USB cable to the SPI interface board, then connect the power adapter to you XBOX 360 but DO NOT turn on it. Just plug the power plug to the wall outlet and power connector to your xbox 360.
So all the cable connections are ready, you can then following the instruction mentioned in [here] (start from page 7, 4.Reading out the NAND to page 13) to read the nand and write the NAND. Make sure to use interface USB, so the command to read NAND is:
nandpro usb: -r16 nandback.bin
Soldering the SMC-JTAG connection
Read "Soldering the SMC-JTAG connection" at:
How to JTAG XBOX 360
